MODEL- ELIMINATOR         VENDOR- COOLIT INC
  
FEATURES- Eliminator Thermoelectric CPU Cooler
       The Eliminator is recommended for CPUs with a total heat output of 
        up to 125W. The Eliminator is targeted for overclocking nearly any 
        dual core CPU while the Freezone is more than capable of cooling 
        the new quad core kentsfield from Intel.
        Eliminator has 3 TECs with a total maximum power draw of 40W. 
        The Thermal Control Module (TCM) on the Eliminator has 3 settings - 
         low, medium and high. "Low" is intended for very low power CPU's 
         in a multimedia setting where there is a desire for very low noise 
         output. "Medium" will be more than adequate cooling for day to day 
         activities as well as gaming for stock processor speeds. "High" is 
         maximum cooling power for the overclocking enthusiasts.
* Patented FHE Design Promotes Heat Transfer
   The Eliminator CPU Cooler is equipped with a CPU FHE (Fluid Heat 
   Exchanger, or cold plate) that is monolithic (a solid piece of) copper. 
   This FHE is designed to absorb high thermal flux from an area with high 
   thermal density (i.e., it is very effective at removing a lot of heat 
   from a very small surface). 
* Integrated Design
   The Eliminator CPU Cooler patented chiller module has an integrated 
   reservoir, which consists of a high flow DC pump and expansion chamber. 
   Combining the Chiller and the Pump into a single module is a space-
   saving design that allows for ease of installation.
* Regulated Temperature Control
   Because of the extreme cooling capacity the Freezone product provides, 
   there is a TCM (Thermal Control Module) built into the system to protect 
   against over-cooling and condensation.  The TCM regulates the amount of 
   power that is applied to the TECs and exhaust fan.  The TCM will 
   automatically vary system level output to adjust for changes in both 
   ambient temperature and CPU load.  This complies with Energy Star 
   standards.
* Adjustable User Settings 
   The factory TCM setting will automatically adjust the system to run 
   silently during low load operations and boost cooling power under heavy 
   loads and/or adverse environmental conditions.  Since the TCM regulates 
   the TECs as cooling boosters, it is far more effective than simple fan 
   speed regulation.  If the user desires, the TCM can be manually adjusted 
   to suit the preferences of an individual user.  For example, if the user 
   intends to enhance the performance of a CPU, the TCM can be adjusted to 
   reduce the coolant temperature and thus reduce the operating temperature 
   of a CPU; if the user requires continuous silent operation, the TCM can 
   be safely adjusted to reduce power output to the TECs and exhaust fan. 
* Maintenance-Free Operation
   The Eliminator CPU Cooler requires less maintenance than air or water-
   cooling systems. The liquid system itself is factory-sealed and a closed 
   loop constructed with vapor resistant materials and fitted with gas 
   resistant plumbing. This way, the Eliminator CPU Cooler never requires 
   refilling, for the entire life of the system.  The chiller module itself 
   has a heatsink that promotes laminar air-flow through the fins.  Laminar 
   flow ensures that dust, dirt and particulates simply pass through the 
   fin array, while promoting maximum thermal transfer.  The only 
   maintenance the Eliminator CPU Cooler system requires is the occasional 
   dusting of the exhaust fan. This can be accomplished in a few seconds 
   using compressed air, or gas.
* Environmentally Friendly Coolant
   The coolant in the liquid loop is composed of Low-Tox PPG (polypropylene 
   glycol) and distilled water. This mixture is environmentally friendly, 
   promotes enhanced cooling and reliability, and it is recyclable.  Unlike 
   water cooling systems, the Eliminator CPU Cooler only contains about 125 
   CCs (half a cup) of coolant. The coolant temperature is tightly 
   regulated by the TCM in real time. That means the Eliminator CPU Cooler 
   does not require a large reserve of coolant to act as a temporary heat 
   dump for low duration operations at high loading. In fact, the 
   Eliminator CPU Cooler's duty cycle is designed for 100% operation under 
   continuous maximum loading.
    
  -- SPECIFICATIONs -----------------------------------
CPU FHE      - (Fluid Heat Exchanger)
               Design      : Monolithic copper, multi-cell, single channel
               Dimension   : 42 x 42 x 17 mm
               Weight      : 195 grams
TCM          - (Thermal Control Module)
               Design      : Dual IC SMT PCB w/outboard IC sensor 
               Input       : 12VDC, 5VDC 
               Weight      : 89 x 53 mm 
               Function    : Thermal controller to adjust TEC and fan power 
                               output.
CHILLER & PUMP MODULE- (Heatsink)
               Design      : 3-way dissipation plate, anodized alloy, 
                               laminar flow array.
               Dimension   : 105 mm (diameter) x 60 mm (deep)
               Weight      : 380 grams
                       (TECs)
               Design      : Three solid-state heat pump wafers 
               Dimension   : 40 x 40 x 3.5 mm (each) 
               Weight      : 20 grams (each) x 3
               Function    : Active coolant thermal reduction 
                       (Chiller FHE's): 
               Design      : Tri anodized alloy distribution, multi-
                               channel w/laminar flow.
               Dimension   : 41 x 41 x 12 mm (each) 
               Weight      : 32 grams (each) x 3
                       (Fan)
               Noise       : 34dBA
               Bearing Type: Enhanced life ceramic 
               Life Cycle  : 50,000 hrs 
               Dimension   : 92 x 92 x 38 mm 
               Function    : Heatsink convection, chassis exhaust 
                       (Pump and Reservoir)
               Design      : 12VDC coreless outrunner pump w/integrated 
                               expansion vessel.
               Bearings    : Dual in fluid sapphire bearings 
               Noise       : <15dBA 
               Life Cycle  : 50,000 hours
               Dimension   : 50 x 50 x 75 mm 
               Weight      : 360 grams
www.CoolitInc.com